PhreakMods EX-Groove Link quick release shaft

PhreakMods EX-Groove Link Quick Release Shaft This article provides information on how to install the

PhreakMods EX-Groove Link Quick Release Shaft of theClick here to see the product.


PhreakMods EX-Groove Link Quick Release Shaft Installation Movie

 Necessary Parts for Installation

Prepare Sanwa Denshi JLF-TP-8YT series or HORI HAYABUSA joystick and PhreakMods EX-Groove Link.
Note that the PhreakMods EX-Groove Link alone will not function as a joystick lever.

The description for this time isThe installation method is the same for the HORI HAYABUSA joystick.


The accessories arePhreakMods EX-Groove Link itself and a hex wrench are included.
The hex wrench is used to tighten the lever ball.
I would like to install it immediately.

Prepare JLF-TP-8YT series joystick.

Remove the shaft cover and dust washer.

Start working from the back side.

Main GuideGT-8FRemove the main guide GT-8F.

Remove the switch substrate TP-MA.

Remove the E-ring JLF-E.


Remove actuator JLF-P-5.

Remove the spring JLF-SP.

Remove spring stopper JLF-P-6.

Remove the main shaft JL-S9F, so it will look like this.

Attach the shaft part of the PhreakMods EX-Groove Link quick release shaft to the pivot JLF-P-4.
Spray grease on the moving parts at this time if necessary.

Recommended grease is Shin-Etsu Chemical G501, because it is used in Seimitsu Kogyo's joysticks and for plastic lubrication.
Mitsuwa Denshi's grease is Shin-Etsu Chemical G-40M, this is for high temperature lubrication and general use. It will be suitable for lubrication of sealed bearings, please choose according to your preference.

Some people often use Tamiya's grease for mini 4WD and RC cars, but we do not recommend it because of its different application and viscosity.

Prepare JLF-P-2 body for JLF.

Set the pivot JLF-P-4, to which the shaft of the PhreakMods EX-Groove Link quick release shaft was attached, to the JLF-P-2 body for JLF.
Spray grease on the moving parts as needed.

Turn over and move to the back side. Install the various parts in the reverse order of the previous step.

Attach the spring stopper JLF-P-6.

Attach the spring JLF-SP.

Install actuator JLF-P-5.

Install the E-ring JLF-E.

Install the switch substrate TP-MA.

Install the main guide GT-8F.

Prepare the main shaft part of the PhreakMods EX-Groove Link quick release shaft, one dust washer (important), and the lever ball.

Put one dust washer (important) in the main shaft of the PhreakMods EX-Groove Link quick release shaft.

Temporarily fasten the lever ball to the main shaft of the PhreakMods EX-Groove Link quick release shaft.

Tighten the lever ball with the hex wrench provided with the PhreakMods EX-Groove Link quick release shaft.

Attach the main shaft of the PhreakMods EX-Groove Link quick release shaft to the joystick lever body to complete.
At this time, the dust washer should be in one piece. If this is a Sanwa Denshi JLF-TP-8YT series or HORI HAYABUSA joystick, two basic dust washers are used.
Since the main shaft of the PhreakMods EX-Groove Link quick release shaft is removable, two washers can get caught in the main shaft and cause it to come off or malfunction, so please be sure to use only one dust washer.
A video of the pickup and delivery process is also available for easy understanding.



RELATED ARTICLES